Today at CES2020, Arduino launched their new hardware Portenta H7 IoT Board. It is feature packed IoT embedded hardware specially meant for serious professional developer.
“By combining the power and flexibility of our production ready IoT hardware with our secure, scalable and easy to integrate cloud services, we are putting in the hands of our customers something really disruptive,” commented Arduino CEO Fabio Violante. “Among the millions of Arduino customers, we’ve even seen numerous businesses transform from traditional ‘one off’ selling to subscription-based service models, creating new IoT-based revenue streams with Arduino as the enabler. The availability of a huge community of developers with Arduino skills is also an important plus and gives them the confidence to invest in our technology”.
Arduino Portenta H7 Features
As per Ardunio, Arduino Portenta H7 module is the first member of the family, it has a dual-core Arm Cortex-M7 and Cortex-M4 operating at 480MHz and 240MHz, respectively, with industrial temperature-range (-40 to 85°C) components.
Portenta can run processes created with TensorFlow
The Arduino Portenta H7 is based on the ST Microelectronics STM32H747, XI series microcontroller.
|Microcontroller||STM32H747XI dual Cortex®-M7+M4 32bit low power ARM MCU (datasheet)|
|Radio module||Murata 1DX dual WiFi 802.11b/g/n 65 Mbps and Bluetooth 5.1 BR/EDR/LE (datasheet)|
|Board Power Supply (USB/VIN)||5V|
|Secure Element (default)||NXP SE0502 (datasheet)|
|Supported Battery||Li-Po Single Cell, 3.7V, 700mAh Minimum (integrated charger)|
|Circuit Operating Voltage||3.3V|
|Current Consumption||2.95 μA in Standby mode (Backup SRAM OFF, RTC/LSE ON)|
|Display Connector||MIPI DSI host & MIPI D-PHY to interface with low-pin count large display|
|GPU||Chrom-ART graphical hardware Accelerator|
|Timers||22x timers and watchdogs|
|UART||4x ports (2 with flow control)|
|SD Card||Interface for SD Card connector (through expansion port only)|
|Operational Temperature||-40 °C to +85 °C (excl. Wireless module) / -10 °C to +55 °C (incl. Wireless module)|
|MKR Headers||Use any of the existing industrial MKR shields on it|
|High-density Connectors||Two 80 pin connectors will expose all of the board’s peripherals to other devices|
|Camera Interface||8-bit, up to 80 MHz|
|ADC||3× ADCs with 16-bit max. resolution (up to 36 channels, up to 3.6 MSPS)|
|DAC||2× 12-bit DAC (1 MHz)|
|USB-C||Host / Device, DisplayPort out, High / Full Speed, Power delivery|
Arduino Portenta H7 Carrier Board
The Portenta Carrier board extends lot of capabilities of the Portenta H7 board through connectors and peripherals that do not physically fit on it. There are connectors for USB, Ethernet RJ-45, CAN bus, MicroSD Card, audio in and out lines, Camera, DisplayPort, etc.
PORTENTA CARRIER TECH SPECS
|FORM FACTOR||eNUC form factor from SGET|
|ETHERNET||Gigabit Ethernet connector (RJ-45)|
|USB HUB||2x female connectors|
|SD CARD||microSD connector|
|CELLULAR NETWORK||NBIoT / CatM1 / GPRS Modem & SIM card connector|
|LORA®||Murata CMWX1ZZABZ LoRa® module|
|POWER||Through external supply, or on-board battery connector|
|GPIO||General GPIO connector, 40 pins|
|VIDEO INPUT||8-bit LVTTL/2 lane MIPI|
|ANTENNAS||2x antenna connectors|
|AUDIO||3x audio-jacks for in- or output of analogue sound|
|EXTERNAL MODULES||Via miniPCIe connector|
|CAN BUS||Via RJ-9 connector|
|RS232 / 422 / 485||Via RJ-11 connector|
I am very excited to see Arduino launching these new boards.
The new Arduino Portenta H7 is now available for pre-order on the Arduino online store, with an estimated delivery date of late February 2020. I have already placed a pre-order request on their website.
If you have any suggestions or feedback please share it in the comments below or send me an email here.
Read my other articles on Embedded System Design.